Ball Joints Critical To Steering, Suspension - Tire Review Magazine

Ball Joints Critical To Steering, Suspension

How do you fix an air ride suspension that has gone flat?

Ball joints are chassis components that eventually wear out and have to be replaced. But the ball joints on many late-model vehicles are now part of a unitized control arm assembly rather than a separate component. The car makes do this to save weight and cost (for them, not your customers!). So on many of these applications, your customer has to buy a complete control arm assembly rather than an individual ball joint if their vehicle needs a new ball joint.

On some of these unitized control arm applications, it is possible to replace the joint separately even though the control arm was not designed that way. Aftermarket chassis parts suppliers are very clever at coming up with ways to save your customers money, so if it’s possible to press a ball joint out of a unitized control arm they probably have a replacement joint that will fit. But if it is not possible to replace the joint, your customer will need a whole new control arm assembly.

On applications where the ball joints can be replaced, installation may require unbolting the joint, pressing out the joint or drilling out rivets that hold the old joint in place. The degree of difficulty can vary greatly from one application to the next, so some DIYers may not know what they’re getting into until they start to tear their car apart.

A classic symptom of worn ball joints is suspension noise when hitting bumps (clunks and rattles), and inner shoulder wear on the front tires due to camber misalignment. Ball joint wear can be checked by raising the wheels off the ground and using a small pry bar with light pressure only
to check for excessive movement in the joint or looseness. Some ball joints have built-in wear indicators that indicate wear when the wheels are on the ground.

Either way, it’s time to replace the joint if wear exceeds factory specifications.

On cars and trucks that have short long arm (SLA) suspensions, there are four ball joints: one upper and one lower on each side. The load bearing joint (which may be the upper or lower depending on where the spring is located) is the one that experiences the most wear.

On cars with MacPherson strut suspensions, there are no upper ball joints — unless it has a “wishbone” strut suspension with upper control arms, in which case there will be upper ball joints.

If one ball joint is worn out, chances are the ball joint on the opposite side is also bad or nearing the end of its service life. Many technicians recommend replacing both joints at the same time (both lowers, both uppers or all four).

Another item that should be checked when ball joints are replaced is the stud hole in the steering knuckle — especially if the ball joint stud has broken or is loose. An out-of-round hole can allow flexing that leads to metal fatigue and stud breakage. The new ball joint stud should fit snugly in the hole without rocking, and only the threads of the stud should extend above the hole.

On front-wheel drive suspensions that use a pinch bolt arrangement to lock the ball stud in the knuckle, the pinch bolts are often torque-to-yield and should not be reused but replaced with new bolts.

Other steering and suspension parts that may be worn out and in need of replacement include tie rod ends, control arm bushings, idler arms, steering rack bellows and rack mounts. These parts should also be inspected and replaced as needed when the ball joints are replaced.

Finally, wheel alignment should be checked and adjusted to specifications as needed following the installation of new ball joints or unitized control arm assembles. If the wheels are not aligned, tire wear, steering and handling may all be affected.

You May Also Like

Maximizing Motorcycle Safety and Performance with TPMS

While TPMS has been mandated for passenger vehicles in the U.S. and other countries, motorcycles are not yet a part of this legislation.

TPMS-Talk-Motorcycles-1400

The thrill of riding a motorcycle is unmatched, offering a sense of freedom and adventure. However, this exhilaration comes with its own set of challenges, demanding a higher level of awareness and control. Proper tire pressure is essential for safe and smooth rides, and this is where Motorcycle Tire Pressure Monitoring Systems (TPMS) come into play. Tire Pressure Monitoring Systems (TPMS) have become increasingly popular in the motorcycle world, playing a pivotal role in ensuring the safety of riders.

The Average Price/Wait Time on an Oil Change from Mobile Repair Providers

Data was collected for a synthetic oil & filter change and tire rotation.

Auto-Maintenance-Oil-Change
The Real Value of TPMS Retrofit Kits

The market offers various kit types catering to diverse needs and preferences.

TPMS-Retrofit---Classic-Car-Lot-1400
Step by Step: How to Properly Change an EV Tire

Tire changing is a straightforward procedure for most technicians, but the transition from ICE vehicles to EVs will introduce some changes.

EV on Lift
Mounting & Demounting a Tire the Correct Way

In both rim clamp and pedestal tire changers, specific techniques are followed to ensure correct dismounting and mounting of tires.

Reverse-wheel-adapter

Other Posts

Why Updating Your TPMS Tools Regularly Matters

To maintain the accuracy and reliability of newly programmed TPMS sensors, it’s important to keep your TPMS programming tool up to date.

TPMS Stock
Check TPMS, Save on Fuel for Your Next Road Trip

Discover the benefits of TPMS for enhancing safety, fuel efficiency and peace of mind during long road trips.

TPMS-relearn
Troubleshooting Porsche TPMS

Tips for diagnosing Porsche TPMS systems and performing relearns.

Porsche TPMS
Tire Mounted Sensors: The Future of Intelligent Tire Sensing

Tire-mounted sensors offer expanded capabilities for TPMS technology advancement.

Tire-Mounted-Sensor