Defining Truck Tire Underinflation - Tire Review Magazine

Defining Truck Tire Underinflation

[Editor’s Note: This article by Asa Sharp appeared in the February 2014 issue of Fleet Equipment magazine, a sister publication of Tire Review.]

Defining underinflation seems like a simple enough question, and it actually is simple if we’re talking solely about passenger cars or light-duty trucks. The answer for these vehicles is easily found in the owners manual under the alphabetical index labeled “tires.” Easier yet, all new cars/light trucks manufactured in the last three or four decades are required to be labeled with the recommended tire size and inflation pressures on a placard typically placed on the left front door jamb or inside the flip out fuel filler door. This is not the case, however, for Class 5-8 highway trucks.

These working freight haulers are used in a wide variety of service conditions; carry loads ranging from steel coils to feather mattresses and anything in between. Also, a mere five popular tire sizes are employed to outfit approximately 90% of this wide array of vehicles. This limited number of tire and wheel sizes helps to maximize vehicle flexibility, simplify purchasing, inventory, maintenance, in-route servicing, retreading and even final disposal. A wide range of gross vehicle weight ratings (GVWRs) are covered, but more importantly, a vast diversity of loads, service conditions and vehicle configurations are addressed with this small number of tire/wheel sizes and load ranges.

One noteworthy point is that the sidewall stamping for passenger and light truck tires is stated as a “maximum load rating at a maximum inflation pressure.” Medium and heavy truck tires, on the other hand, are stated as maximum load ratings at an accompanying (but not maximum) inflation pressure. Load ratings for these tires may be changed primarily for certain speed restrictions; but, more importantly, inflation pressures may be adjusted, both up or down, when actual loads being carried are different from the loads shown on the tire sidewall stamping. These basic ratings and a number of permissible adjustments for actual service conditions are standardized. Therefore, all tires of a given size designation have the same ratings regardless of manufacturer, by the Tire and Rim Association (TRA). Essentially, a sliding scale showing actual service loads with accompanying minimum cold inflation pressures details the basis for establishing minimum required inflation pressures. In many cases, these values may be significantly different from those shown on the tire sidewall stamping.

The bottom line here is that determining the proper inflation and therefore, defining whether the tire is over or under inflated, is only possible by knowing the actual load and service conditions. Note also that actual truck tire loads are usually different by axle. While it is normally assumed that loads are equally distributed side-to-side, it is necessary to obtain individual axle weights, and then consult the TRA tables to determine whether a tire is under or over inflated.

One other complication is that the TRA tables are expressed in “cold” pressures, which is normally defined as approximately 65 to 70 degrees F. It is normal for truck tires in linehaul service to increase pressures from heat buildup approximately five to as much as 20 psi over “cold” conditions. This buildup varies primarily with speed, load, ambient and road surface temperature. Therefore, the most accurate inflation pressure checks are pre-trip or after the tires have been at rest for two hours following use at highway speeds. Some fleets have determined an accurate cold to hot pressure relationship based on vehicle types, service conditions, especially typical axle loads, speeds and other variables. However, in-route service providers or inspection personnel would not know this information.

There is no accurate way to define underinflation based on the truck tire sidewall stamping. A number of other variables discussed above must be considered for an accurate definition.

Knowledgeable tire manufacturers are able to assist in the determination of optimum inflation pressures to assure safety, maximize tread life and to obtain casing longevity for multiple retreads.

You May Also Like

Auto Care Association CEO Urges Trump to Keep U.S.-Mexico Border Open for Trade

The Auto Care Association is urging President Donald Trump’s administration to keep the border between the U.S. and Mexico open with the majority of imported auto parts coming from Mexico.

Auto Care Association

The Auto Care Association is urging President Donald Trump's Administration to keep the border between the United States and Mexico open for business.

Bill Hanvey, president and CEO of the Auto Care Association, said between the U.S. and Mexico, millions of dollars of auto parts are shipped back and forth daily.

Gallery: GT Radial Maxtour LX Launch & Plant Visit

This week, Giti Tire USA hosted a launch event to debut its new touring tire under the GT Radial brand, the Maxtour LX. Related Articles – Smart Walls Help Bays Stay Organized – Yokohama Rubber: Sales Up, Earnings Down in 2018 – Smithers Rapra Opens New Product Testing Lab In Suzhou, China During a ride-and-drive

Giti Tire plant team Richburg SC
Smart Walls Help Bays Stay Organized

JohnDow Industries Smart Walls are designed as a better option for the storage of popular service parts, making them easy to access, easy to find and easy to organize.

Yokohama Rubber: Sales Up, Earnings Down in 2018

The Yokohama Rubber Co., Ltd., announced its business and financial results for fiscal year 2018.

Smithers Rapra Opens New Product Testing Lab In Suzhou, China

Smithers Rapra is opening a new product-testing lab in Suzhou, China, which will provide air leak and burst, cleanliness, material properties, salt spray, and pressure, vibration and temperature (PVT) testing.

Smithers-Rapra China facility

Other Posts

Andreoli Software Integrates With AMI

Andreoli Software, a point-of-sale software provider to the independent retail and wholesale tire industry, has released an integration with AutoMed5, or AMI.

Explaining Types of TPMS Sensors in Terms of Music

With multiple types of TPMS sensors, deciding which one is right for your business starts with a good understanding of each.

music on demand TPMs sensors
Continental Tire Announces Price Increases for U.S. Market

Continental Tire the Americas will increase prices in the U.S. market on Continental and General brand passenger and light truck tires, effective Jan. 7, 2019.

Michelin Acquires 2019 Naming Rights to Road Atlanta Racetrack

Michelin North America has announced an agreement with Road Atlanta for exclusive naming rights of the racetrack. Beginning in 2019, the track will be renamed Michelin Raceway Road Atlanta.