Active Wheel Speed Sensor Diagnostics - Tire Review Magazine

Active Wheel Speed Sensor Diagnostics

Learn the difference between active and passive wheel speed sensor diagnostics.

There are two "types" of sensors generally found on the modern car –the passive speed sensor and the active speed sensor. They both perform the same function, but work entirely different. The passive speed sensor uses a magnet with fine copper wire wrapped around it to create its own alternating magnetic field. The polarity changes from positive to negative as the tone ring passes by the magnetic field. This frequency changes with wheel speed.



The newer active sensor uses a digital signal created by the ABS controller. This type of sensor uses a hall effect or a variable reluctance signal with a square wave pattern. The sensor consists of two wires; one is used as the positive (DC) voltage from the controller and the other lead as the return (Ground) to it. The advantages of the active speed sensors are their ability to read more accurately at slow speeds than the passive speed sensors. They don’t have to self-generate the needed voltage by the spinning action of the wheel. Also, since these sensors use a DC voltage, they can detect not only the speed of the wheel, but the direction of travel. This allows the controller the ability to calculate not only wheel speed, but can also be used for the hill holding and hill descent control features found on some vehicles.

How Does It Work

The active speed sensor or “Magneto Resistive Sensor” consists of two parallel resistors and a magnetic material located at a precise distance from a permanent magnet. The resistors are about 1.4k ohms each, however if you were to measure the resistance at the wire ends you would probably see 5 to 6 mega ohms.  (That’s because you are reading the resistance values of the not only the resistors but the magnetic material inside the sensor.) These parallel resistors work together to create the voltage changes you’ll see on your lab scope as the tone wheel passes by the internal magnet. The tone wheel (if flattened out) looks like the square wave pattern it creates. As the high part of the tone wheel’s tooth is near the sensor, a higher voltage is created while the opposite is done when the lower part of the tone wheel is near the sensor.


Even though it is close to battery voltage at the sensor (10.6v is what I’ve found) you won’t be able to use a test light to read it.  A test light consists of a ground lead, a bulb (resistance), and the positive end, which is basically the same thing the sensor has internally minus the magnets. If you try stabbing a test light on the positive lead to the sensor, the computer sees that as a possible short to ground.  Meaning, it thinks your test light is the sensor because the return voltage on the ground side of the sensor has drastically changed.  In fact, in most of these ABS systems, if you do “short” the lead, the processor shuts that sensor off (0.0v) until the next key cycle. This way it avoids any harm coming to the internal circuits of the processor.  But, if you continued to check the circuit without turning off the key, you’d end up back at the processor and more than likely come to the conclusion the processor is bad.  It’s not … just cycle the key and recheck it.

Testing an Active Speed Sensor

The best tool for testing the active speed sensor is a good scanner, preferably one that can show the separate speed sensors in graph form. A lab scope is probably the best for a more precise answer and can be attached directly at the sensor to read the individual sensors or wires rather than the entire system as with the scanner. But if you’re looking for a quick test to determine if just the speed sensor is in working order, you can make a quick little tester yourself.

LED Tester

You’ll need a 220 ohm resistor, an LED and a 12v battery source. Disconnect the sensor from the car (DO NOT TRY THIS WITH IT HOOKED UP!), and hook up the battery to one side of the sensor leads.


The other lead from the sensor is hooked up to your resistor and LED, while the remaining lead from your LED should return to the battery.  An LED is polarity conscious, be sure to have the current flowing in the right direction or it won’t light up at all. (The sensor doesn’t care which direction, just the LED does). What you’ll see as you spin the wheel is your LED blinking on and off with an increasing and decreasing blink rate as the wheel speed changes.


This is one of those times when the old school test light isn’t going to help you out at all; in fact, it might create more of a problem. Your scope or your scanner on these types of sensors is the better choice. However, this quick little LED tester might help you with your diagnostics. It won’t test the entire system, but it will confirm if the speed sensor is functioning. Testing is always better when you have more than one method to determine the condition of a component. In this case, a scanner, a scope or a homemade LED tester can help you in diagnosing these active speed sensors.  


Always test first, test second … and when still in doubt … test a third time.  


About the Author

Scott “Gonzo” Weaver

[email protected]



Scott “Gonzo” Weaver is the owner of Superior Auto Electric in Tulsa, Okla. and has owned the shop for 27 years. He was given his trademark nickname “Gonzo” while serving in the USMC. He is the author of the book “Hey Look! I Found the Loose Nut”, that can be purchased online at or at

You May Also Like

Maximizing Motorcycle Safety and Performance with TPMS

While TPMS has been mandated for passenger vehicles in the U.S. and other countries, motorcycles are not yet a part of this legislation.


The thrill of riding a motorcycle is unmatched, offering a sense of freedom and adventure. However, this exhilaration comes with its own set of challenges, demanding a higher level of awareness and control. Proper tire pressure is essential for safe and smooth rides, and this is where Motorcycle Tire Pressure Monitoring Systems (TPMS) come into play. Tire Pressure Monitoring Systems (TPMS) have become increasingly popular in the motorcycle world, playing a pivotal role in ensuring the safety of riders.

The Average Price/Wait Time on an Oil Change from Mobile Repair Providers

Data was collected for a synthetic oil & filter change and tire rotation.

The Real Value of TPMS Retrofit Kits

The market offers various kit types catering to diverse needs and preferences.

Step by Step: How to Properly Change an EV Tire

Tire changing is a straightforward procedure for most technicians, but the transition from ICE vehicles to EVs will introduce some changes.

EV on Lift
Mounting & Demounting a Tire the Correct Way

In both rim clamp and pedestal tire changers, specific techniques are followed to ensure correct dismounting and mounting of tires.


Other Posts

Why Updating Your TPMS Tools Regularly Matters

To maintain the accuracy and reliability of newly programmed TPMS sensors, it’s important to keep your TPMS programming tool up to date.

TPMS Stock
Check TPMS, Save on Fuel for Your Next Road Trip

Discover the benefits of TPMS for enhancing safety, fuel efficiency and peace of mind during long road trips.

Troubleshooting Porsche TPMS

Tips for diagnosing Porsche TPMS systems and performing relearns.

Porsche TPMS
Tire Mounted Sensors: The Future of Intelligent Tire Sensing

Tire-mounted sensors offer expanded capabilities for TPMS technology advancement.